Outdoor-heaters – Zcooling A-Z cooling

Outdoor Gas Heater

admin — Sun, 18 Sep 2016 13:46:33 +0000

Dry Weight (kg)

Dimensions (mm)

Height	2,200
Width	650
Depth	620

2.7kW Electric Outdoor heater

admin — Sun, 18 Sep 2016 13:44:06 +0000

Heating Capacity (kW)

Controls

Remote control & on/off switch

Voltage (ph-volt/Hz)

230/50

Dry Weight (kg)

Dimensions (mm)

Height	1,680
Width	420
Depth	390

Electric Patio Heater

admin — Sun, 18 Sep 2016 13:41:48 +0000

Heating Capacity (kW)

Power Requirement (ph/v/Hz)

1/230/50

Safety Devices

Overheat safety cut off

Dry Weight (kg)

12.8

Dimensions (mm)

Height	560
Width	540
Depth	280

Gas Outdoor Heater Pyramid Flame Tower

admin — Sun, 18 Sep 2016 13:35:46 +0000

9.3kW pyramid flame tower patio heater
Modern design
Stainless steel construction
Low gas consumption
Large cylinder enclosure
Ambient light effect
Built-in electric ignition
Adjustable heat settings
Toughened centre tube

Precautions  Ensure the connection to the gas bottle has been tightly secured with a spanner where necessary.  Leak test all connections after each bottle re-fill  Never check for leaks with a match or open flame  Do not store or use gasoline or other flammable vapours and liquids in the vicinity of this or any other appliance  Any LPG bottle not connected for use shall not be stored in the vicinity of this or any other appliance For your safety – if you smell gas Turn off the gas supply at the bottle. Extinguish all naked flames; do not operate any electrical appliances. Ventilate the area. Check for leaks as detailed in this manual. If odour persists, contact London Cool immediately on 0800 440 444. FOR OUTDOOR USE ONLY The use of this appliance in enclosed areas can be dangerous and is PROHIBITED. Using this product in an enclosed area may cause injury, death or property damage. Read the instructions before using this appliance. This appliance must be installed in accordance with instructions and local regulations. WARNING!  For use outdoors or in amply ventilated areas  An amply ventilated area must have a minimum of 25% of the surface area open  The surface area is the sum of the walls surface Do not use this heater in an explosive atmosphere. Keep the heater away from areas where gasoline or other flammable liquids or vapours are stored. Prior to use, check for damaged parts such as hoses, regulators, pilot or burner. Do not move the heater when in operation. Shut off the valve at the gas cylinder before moving the appliance. Disconnect the LPG bottle before moving the heater. Do not attempt to alter the unit in any manner, e.g. using the heater without the top canopy reflector or radiant screen. The appliance shall not be used in basements or above ground level. It must always be placed on a solid level surface. Always ensure there is ample fresh air ventilation. Never replace or substitute the regulator with any other regulator other than the factory suggested replacement. Do not clean the heaters with cleaners that are combustible or corrosive. Do not paint radiant screen, control panel or top canopy reflector. All leak tests should be done with a soapy solution. NEVER USE AN OPEN FLAME TO CHECK FOR LEAKS. The LPG gas bottle valve and regulator should be turned off when the heater is not in use. Do not use when it is raining, always be careful not to let any liquid splash the glass tube when the heater is working. Keep children away from the heater, always be careful not to knock over the heater which will break the glass tube and may cause injury. The following clearance distances are required for safe operation when using this heater. It is important you keep these distances from combustible materials: minimum clearance to adjacent combustibles: from top: 61cm, from sides: 60cm. Check the heater immediately if any of the following exists: 1. The smell of gas 2. The heater does not reach temperature 3. The burner makes a popping noise during use (a slight popping noise is normal when the burner is extinguished after use) If you smell gas, turn off the valve immediately. If the smell persists, contact London Cool immediately. The propane hose with regulator assembly shall be located out of the pathway where people may trip over it or in areas where the hose will not be subject to accidental damage. Children and adults should be aware of the high surface temperature hazard, and should keep a safe distance away to avoid clothes burning or igniting. Young children should be carefully supervised when they are in the area of the heater. Clothing or other flammable material should not be hung from the heater, or placed on or near the heater. Any guard or other protective device removed for servicing the heater must be replaced prior to operating the heater. Installation and repair should always be carried out by a qualified service person. The heater should be inspected before use and cleaning may be required at least once a year, or as necessary. It is imperative that the control compartment, burner and circulating air passageways of the heater be kept clean. Keep the appliance area clear of combustible materials such as gasoline and other flammable vapours and liquids. Do not obstruct the flow of combustion and ventilation air. Do not obstruct the ventilation holes of the cylinder housing. Keep the ventilation opening of the bottle enclosure free and clear of debris. Note: when changing the bottle, the appliance must be in a amply ventilated area and must be away from any ignition source (candles, cigarettes, other flame producing appliances). Avoid twisting the flexible tubing while using. Never use the appliance near a fire hazard. WARNING! The appliance must ONLY be used for outdoor use. The installation of fixed appliances shall only be carried out by competent persons and be in accordance with the relevant codes of practice. Regularly check the gas hose and if necessary, replace the gas hose. This appliance requires a regulator. Combustible materials are considered to be wood, compressed paper, plant fibres, and plastic, Plexiglas or other materials capable of being ignited or burned. Such materials shall be considered combustible even though flame proofed, fire-retardant treated or plastered. Additional clearance may be required for glass, painted surfaces and other materials which may be damaged by radiant or convection heat. The hose assembly should be properly located out of pathways where people may trip over it. The hose must be protected from contact with hot or sharp surfaces both during use and while in storage. The hose assembly should be visually inspected prior to each use of the heater. If excessive abrasion or wear is evident, or the hose is cut, it must be replaced prior to operating the heater. The replacement hose assembly may be obtained from the manufacturer. DO NOT use any pressure regulator or hose assembly other than those supplied with the appliance or provided by your gas supplier. Replacement pressure regulator and hose assembly must be those specified. Replacement parts may be obtained from the manufacturer or London Cool. The valve outlet must be maintained in good condition. When the bottle is not in use, be sure to cover it with a dust cap. A leak test should be performed with soapy water whenever connecting a new bottle of gas. NEVER use a match to test for leaks. The propane bottle must be turned off whenever the heater is not in use. When the heater is to be stored indoors, the propane bottle and the heater must be disconnected and the bottle stored in accordance with the standard for storage and handling of liquefied gases (i.e. not indoors, but in a dry wellventilated area). The patio heater has been designed with several safety features which include a tip over switch. Any modification to the heater not described in the installation instructions may compromise the safety of this appliance. Special concern is as follows: 1. DO NOT shorten post length; 2. DO NOT bypass thermocouple safety; 3. DO NOT operate heater without a reflector; Clothing and other flammable materials should not be hung from the heater, or placed on or near the heater. The area above the post may be extremely hot. Direct contact with these metal surfaces should be avoided in order to prevent burns or clothing ignition. Installation Important safety rules: This appliance is for outdoor use only. 1. This appliance shall not be installed indoors, in buildings, garages or any other enclosed area 2. Do not place articles on or against this appliance 3. Do not use or store flammable materials near this appliance 4. Children and adults should be alerted to the hazards of high surface temperatures, burns and clothing ignition. 5. Children should be carefully supervised when they are in the area of the appliance 6. NEVER hang anything including clothes or other flammable items on the appliance 7. Do not operate this appliance unless it is fully assembled with the reflector in place. 8. DO NOT SPRAY AEROSOLES IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION 9. Installation and repair should be done by a qualified service person. The appliance must be inspected before use and at least annually by a qualified service person. More frequent cleaning may be required if necessary. It is imperative that control compartment, burners and circulating air passengers of the heater be kept clean 10. In case of violent wind particular attention must be taken against tilting of the appliance

Commercial Patio Heater

admin — Sun, 18 Sep 2016 13:30:45 +0000

WARNING!  For use outdoors in amply ventilated areas An amply ventilated area must have a minimum of 25% of the surface are open. (See below diagram). The surface area is the sum is the walls surface  Never use in closed areas The use if this appliance in enclosed areas can be dangerous and is prohibited  Use at a distance of at least 2m from inflammable materials  Do not move when lit or just switched off  Always wait until it is cool  In windy conditions secure your heater to reduce the risk of the heater blowing over Operating instructions Please read these instructions carefully before use 1) Turn the lever on the clip on the regulator anti clockwise to open the gas valve on your patio gas cylinder 2) Press the control knob completely down, making sure that it is in the START position (white dote) 3) Press the electronic piezo until the pilot flame lights Once this is lit, continue to press the control know for another 10 - 20 seconds, the release it. Your pilot flame should now remain alight. If not, repeat steps 2 & 3 4) To light the main burner, depress the control knob halfway and turn anti clockwise to MIN or MAX 5) To put the unit in STANDBY, turn the control knob clockwise to the START position 6) To switch the heater off completely, turn the lever on the clip on the regulator clockwise to close the gas valve on the gas cylinder 7) Instructions for electronic ignition to replace battery, unscrew the black cover with the rubber button. (It will require a AA battery) 8) Do NOT operate if under the influence of alcohol or drugs. Description The use of this appliance in enclosed areas can be dangerous and is PROHIBITED The combustion products leaving the heater are very hot. On no account should the heater be used in an enclosed space Ensure that no flammable material is within 2 metres of the heater. Wide areas can be heated according to the thermal input and the atmosphere conditions prevailing at time use This heater does not expel exhaust gases, non-polluting liquid gas fuel is used (Propane) This unit has been approved by the German body TUV in Cologne and complies with current European directives and standards Safety devices installed on the unit  Thermocouple The pilot flame heats an element that, when heated, keeps the gas valve of the heater open. (NOT THE ONE THAT IS ON THE CYLINDER) Within on minute of the pilot flame being extinguished, the gas supply is shut off to the heater control valve  Piezoelectric Lighting Undoubtedly the safest method of lighting because no naked flame has to be approached by hand to the unit  Anti-Tilt Switch If the heater is tilted past an angle of 10° from the vertical plain the gas supply to the heater control valve is shut off Safety rules to be observed  The use of this unit in enclosed areas can be dangerous and is PROHIBITED  Ensure the connection to the gas cylinder is secure and has been tightened with a spanner.  Use ONLY for heating  MAKE SURE that there is no inflammable material within 2m of the unit  MAKE SURE that all other materials are more than 1m from the unit  PAY ATTENTION to whatever may be above the unit when in operation, because:- - At 30 cm from the hood the temperature is 75°C - At 60 cm from the hood the temperature is 58°C - At 90 cm from the hood the temperature is 43°C  WARNING!: Any flammable coating must be at least 1m from the top of the reflecting hood of the unit  DO NOT TOUCH any part of the unit above the area of the control knob as this could be very hot  Always wait at least an hour after switching off the unit completely before touching the parts above the control knob  NEVER cover the apparatus whilst it is being used  DO NOT START the unit if it is not completely assembled  To balance the unit, use cylinders with an empty weight of not less than 11kg  DO NOT USE the unit when there are strong winds  NEVER move the unit when it is lit  NEVER move the unit when it has just been switched off. Wait until it has cooled down and then move it  Whenever the unit is not in use, move the cylinder from its compartment  DO NOT replace the rubber gas pipe with other of more than 1.1m lengths  ALWAYS turn the lever of your clip on regulator to the off position to close the valve on the gas cylinder  CHECK the unit regularly when it is working  DO NOT KEEP the cylinder of liquid in cellars, basements, stairwells, corridors, underground passages, etc.  KEEP the cylinder away from heat sources  A gas cylinder being in position inside the heater will not guarantee that the heater will not be blown over in windy conditions. Be aware! Operation Once the quick-on is correctly mounted on the valve, gas supply is possible by turning the regulator handle upwards (counter clockwise). To shut off the gas supply, reverse this procedure; an arrow engraved on the handle indicates the closing direction. Symbols engraved on the bonnet show how to operate the regulator handle CAUTION! If you are unable to open the regulator handle, this means that your Quick-on is not correctly connected to the valve. Do not force the handle open, start the procedure again Replacing a cylinder Make sure that: - All taps on the heater are in the closed position - The clip-on regulator handle is in the closed position Then remove the clip-on regulator by pressing horizontally on the handle and pulling upwards at the same time DO NOT attempt to carry out this operation with the regulator handle in the open position The clip on regulator can be equipped with a safety device designed to automatically limit the gas escape in case of separation or rupture of the pipe supplying gas to the consuming unit. The marking FLOW LIMITING DEVICE on the identification label means that the clip-on is equipped with this option Operating of flow limiting device The Flow Limiting Device is likely to activate under the following conditions:  Normal operating conditions  Consumption of the gas fired unit is higher than the regulator flow capacity. In such case, contact London Cool on 0121 359 5100 Operating your patio heater We recommend that the first time you use your patio heater, use in the open air as some fumes are given off due to the elimination of the protective lubricants Wait until the unit has cooled down before moving it to where it is going to be used 1) OPEN the valve on the patio gas cylinder by turning the lever on your clip on your regulator ANTI CLOCKWISE to the on position 2) Turn the CONTROL KNOB on the heater completely in a clockwise direction so that the white line points at the white dot. This is in the START position 3) Press and hold down the control knob, wait 40-50 seconds for the gas to fill the pipe, press the electronic piezo button to generate the spark to light your pilot flame. Check through the hole in the burner mesh that the pilot flame is alight 4) Wait a few seconds (10-20), then release the control knob If the pilot light goes out, repeat steps 3 and 4 Now the unit is ready to use. Gently push the control knob and turn it anti clockwise until the knob index corresponds with minimum or maximum according to the capacity required, and in a few minutes (3-5) you will have the heat you need. The models constructed by TMC are pre-set to function: 1) WHITE DOT - Start with only the pilot flame alight 2) SMALL WHITE FLAME - Minimum with the pilot flame alight and the main burner at minimum capacity 3) LARGE WHITE FLAME - Maximum with the pilot flame alight and the main burner at maximum capacity To bring the heater to Start position, turn the control knob clockwise as far as it will go Switching the unit off To switch the unit completely, turn the lever on the clip on the regulator clockwise to the off position. To make operations easier, use the MINIMUM and READY positions for the whole period of use, but make sure the cylinder and the heater are closed completely at the end of every use When not used for a long period The unit itself does not suffer under bad weather but we equally advise you to store it with care If there are problems of space, the reflecting hood can be removed, and the nuts and washers kept safe for future use. (NB: they are all in stainless steel) Remove the cylinder from its compartment, enclose the burner in a plastic bag and cover all the holes in the gas bottle compartment and door This will avoid the risk during the period of non-use (especially in the summer) of the heater being infested by spiders, wasps and other insects Such infestations will adversely affect your heater and are not covered under your warranty guarantee Restarting after a rest period Remove the reflecting hood and clean the underside until as white as possible Remove the burner mesh, clean inside and out with an ordinary cloth (DO NOT USE oily products that would produce fumes when the apparatus is next switched on) Clean around the burner ring and use a rag to remove any cobwebs and dust Re-assemble all the parts Check the rubber gas hose expiry date and replace if necessary with another Continue using the same instructions as above in the section OPERATING YOUR HEATER Maintenance and cleaning  DO NOT clean the unit when it is lit or has only just been switched off  Use a soft clean rag  CHECK regularly that the RUBBER GAS HOSE connecting the regulator and tap CONTROL VALVE is in good order, otherwise replace it  NEVER MAKE ANY MODIFICATIONS to the unit  Eventual repairs must be made by specialised technicians and with original change parts AA BATTERY: The Electronic Piezo Igniter is equipped with one AA Battery and is not a part that is covered under warranty. A battery must be replaced NECESSARILY every year to avoid damage to the Electronic Piezo Ignition